Auto-meter 1490 Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Auto-meter 1490. Auto Meter 1490 User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
1
1
2
2
1 2
4 CYL. / 2 PULSE
6 CYL. / 3 PULSE 8 CYL. / 4 PULSE
DN DN
DN UP UP UP
Lens Cleaning
To prevent scratching the lens when
cleaning, use a mild, soapy solution to
clean. Wipe
lightly with a soft cloth.
Calibration
IMPORTANT: This tachometer is factory calibrated to operate on 8 cylinder
engines. For 4 or 6 cylinder engines, it is necessary to make the proper adjustments to
adapt this tachometer to your cylinder range.
1
3
⁄4"
3
3
⁄4"
3
11
⁄
32"
4
15
⁄
16"
2
3
⁄8"
4
19
⁄32"
3
3
⁄8
" Models
5
" Models
IMPORTANT
WEAR
SAFETY GLASSES
INSTALLATION INSTRUCTIONS
IN-DASH ELECTRIC T
ACHOMETER
For Use on Early Model & Most Electronic Ignitions
®
2650-1033A
Note:
Locate the switch hole on the back of the tachometer. Move each of the two
switches to the proper cylinder selection according to the diagram
illustration on the right. Apply included label over switch hole.
NOTE: This tachometer has an air core meter. With
power o
ff, it is normal for the pointer to leave
zero. When power is applied, the pointer will
move to the correct position.
Figure A.
8 CYL. (4 pulse)- Both switches up.
6 CYL. (3 pulse)- Switch One down, Switch Two up.
4 CYL. (2 pulse)- Both switches down.
If you are unsure of your vehicle s pulse(s) per revolution or specific
calibration requirements, contact Auto Meter s Service Dept. at (815)
899-0851, or go to www.autometer.com/hp/techtips for information.
1
2
SIG LAMP OUT
+12V
GND
GND
LAMP + 12V
SWITCH HOLE
3
3
⁄8 " SIZE SHOWN
Figure A.
Models: 4497, 4498, 4798, 4898
This tachometer operates on most early model
ignitions, factory electronic and high
performance electronic racing ignitions.
Mounting
1. Mount a 3
3
⁄8" tachometer in a 3
3
⁄8" dia. hole and a 5" tachometer in a 4
5
⁄8" dia. hole in the dashboard. (Be careful not to cut the hole
too large.)
2. Cut a
3
⁄8" dia. hole in the firewall for the tachometer wires. Place a rubber grommet in the hole and route the connector wires through
the grommet to the engine compartment.
3. Connect the tachometer wires as shown in the Wiring
Section.
4. Secure the tachometer to the dashboard using the provided bracket and hardware.
QUESTIONS
:
If after completely reading these instructions you have questions regarding the operation or installation of your instrument(s),
please contact Auto Meter Technical Service at 815-899-0801.
You may also email us at service@autometer.com.
Additional information can also be found at http://www.autometer.com/tech_faq.aspx
1
2
- 2650-1033A 1
- SWITCH HOLE 1
- CAUTION! 2
Résumé du contenu
Page 1 - SWITCH HOLE
11221 24 CYL. / 2 PULSE6 CYL. / 3 PULSE 8 CYL. / 4 PULSEDN DNDN UP UP UPLens CleaningTo prevent scratching the lens when
Page 2 - CAUTION!
12 MONTH LIMITED WARRANTYAuto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in
Produits connexes et manuels pour Pour la voiture Auto-meter 1490
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.082 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels