Auto-meter 3859 Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Auto-meter 3859. Auto Meter 3859 User Manual Manuel d'utilisatio
- Page / 1
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
INSTALLATION INSTRUCTIONS
ELECTRIC bOOST/vAC GAUGE
2650-1130-00 Rev. A
12V B
A
TTE
RY
VACUUM “T”
TUBING ADAPTER
NYLON
TUBING
MAP
SENSOR
GOOD ENGINE
GROUND
FIREWALL
+12v CONNECTION
*SEE STEP 8 BELOW
RED
BLACK
Installation
1. Check that you have all parts required for installation, and the engine is cool.
2. Disconnect the negative (-) battery cable.
3. Gauge mounts in a 2
1
⁄16” hole. Use supplied brackets and nuts to secure gauge to dash.
4. Drill 1” diameter hole where wires pass through sheet metal (such as firewall) and install rubber grommet provided . (Grommet will require slit.)
5. Securely mount the MAP sensor to the firewall or inner fender with pressure port facing down. (Bracket fabrication may be required.)
6. Install T-Fitting in a manifold vacuum hose. Attach one end of the nylon tubing to the T-Fitting using a tubing adapter. Connect the other end of the nylon tubing to the MAP
sensor with the other tubing adapter.
7. Connect the white wire to dash lighting or switchable 12v light source.
8. Connect the red power wire to a switched +12 volt source that maintains power during engine cranking. Most vehicles break the electrical connection to accessories while the
engine is being started. If the boost gauge is connected to one of these circuits, the auto zero function will not work properly and inaccurate readings will result. To determine
whether a switched source maintains power during starting, look for electrical accessories in the vehicle that remain on while the engine is being started. Connect the red power
wire to the same circuit that powers one of these accessories. The connection can be tested by turning the key switch from off to on, the pointer will move backward to the stop
pin and then move to zero. Once the pointer has reached zero, start the engine. If the pointer reads vacuum without returning to the stop pin, a suitable connection has been
found. If the pointer moves to the stop pin and then reads vacuum, another power circuit must be found.
Power-Up
The pointer will move backward to the stop pin and then move to the zero box. This procedure is an auto-calibration function and is performed on every power-up. While this test is
being performed, the gauge may make a clicking sound. This is normal.
Electronic Boost/Vac gauges are equipped with an auto zero function used to compensate for operation at varying altitudes. This function takes a pressure reading during the time
that the key switch “flies through” from the ON position to the START position. The reading represents 0 pressure and is used to set the zero point on the gauge each time the engine
is started.
CAUTION!
As a safety precaution, the +12V terminal of this product should be fused before
connecting to the 12V ignition switch. We recommend using a 1 Amp, 3AG fast-
acting type cartridge fuse (Littlefuse
®
# 312 001 or an equivalent).
GROMMET
FUSE
(SEE
CAUTION
BELOW)
PRESSURE
PORT
NOTE:
MAP Sensor should be mounted with PRESSURE PORT facing down.
Failure to do so could result in inaccurate readings due to condensation
in the line. (Bracket fabrication may be required.)
+12v DASH
LIGHTING
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the
original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product
failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of
the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter
must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in
duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter
Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
SERvICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you
need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be
added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (815) 899-0801
Email us at [email protected]
http://www.autometer.com
OPTIONAL
SLIT TUBING
RECOMMENDED
(AVAILABLE AT MOST
HARDWARE STORES)
© 2007 Auto Meter Products, Inc.
The Super Bezel is a registered trademark of Auto Meter Products, Inc.
2650-1130-00 Rev. A 3/23/07
+12v DASH
LIGHTING
WHITE
(for standard incandescent
lit instrument)
FOR INTERNAL LED
LIT INSTRUMENTS
WHITE
GOOD
ENGINE
GROUND
1
Résumé du contenu
Page 1 - Power-Up
INSTALLATION INSTRUCTIONSELECTRIC bOOST/vAC GAUGE2650-1130-00 Rev. A12V BATTERYVACUUM “T”TUBING ADAPTERNYLONTUBINGMAPSENSORGOOD ENGINE GROUNDFIREWALL
Produits connexes et manuels pour Pour la voiture Auto-meter 3859
(1 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.644 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels